DISMANTLING AND ASSEMBLY OF TAILSTOCK ON LATHE PDF

THE effect of wear and tear of the tailstock assembly of a lathe affects the accuracy of the finished product in several different ways. Wear on the bed-ways or. Assembly and Disassembly of Tailstockkiran wangikar Explain Tailstock And Its Components Lathe Machine: Production Lab MechanicalUPSC IAS. Preparing two wooden blocks (used as sleepers) and wire for guiding lead wires will be helpful. Disassemb ly and assemb ly tools. Disassembly and assembly.

Author: Kizahn Kazrasar
Country: Switzerland
Language: English (Spanish)
Genre: Marketing
Published (Last): 27 June 2010
Pages: 196
PDF File Size: 10.21 Mb
ePub File Size: 2.97 Mb
ISBN: 681-4-59894-222-9
Downloads: 5325
Price: Free* [*Free Regsitration Required]
Uploader: Faugore

The pictures that follow are mostly taken in my garage where the forklift unloaded the machine.

Primary Menu

Pulley and carrier cylinder. You see TD, RK knew what he was talking about, an industrial giant, not a midget! Dovetail ways and shims. If that keyway is not milled ahd from one end to the other it could be a feature also preventing the quill from releasing.

Teknatool International

Overall view of the spindle. The hardest surface it should touch off the lathe is wood.

Plus, those beaver marks will be assemly and remind everyone who sees them a hack has worked on this machine. Bookmarks Bookmarks Digg del. It weighs 60 pounds as shown. Also, I have not called Leblond but I am aware that they still sell some parts.

To cut those radii for the threaded antirotation holes you kind of need one- plunging with an end mill is the way to go. You may use these HTML tags and attributes: Thanks in advance for any suggestions. I applaud your asking these questions. The ram simply screws in from the front of the tailstock. The hole in your lzthe for the pin of the wrench has been damaged by folks doing it the brutal wrong way with a drift or screwdriver used as a punch.

It’s used as Bill described, extend the quill until the eject slot is fully exposed, insert the drift until it stops and a light but sharp rap with a light hammer will disengage the taper. I’m pretty sure that LeBlond still supports these newer machines but when you get the price you will probably decide to make it yourself.

  FLATPICKING ESSENTIALS PDF

I keep subtracting these weights from the estimated total ofhoping to end up with nice small numbers for the bed and cabinet so I can roll them downstairs into my machine shop with a Yates appliance dolly.

Tailstock | Jason’s South Bend 9 Rebuild

I pretty much did the opposite of what I did to take dismantlijg apart. Parts 34 and 35 appear to engage the quill somehow. Funny how regional colloquialisms can creep into language, even funnier when one tries to convince others that a large machinery company, dated far earlier than he, therefore closer to the origin of the word, isn’t as well versed in machine nomenclature as he is!

JohnEvansRobert Campbell Jr. Perhaps these photos which no all the tailstock parts laid out will be helpful so you know what you’re dealing with. Dovetail segment at rear of headstock. Finally, I removed the centering screws from the sides of the tailstock and separated it from its base.

There is a hole on the bottom of the brass ring, that I don’t understand. Any suggestions are welcome and all of you have my gratitude for all the help offered so far. Just make sure your feet are out of the way.

The cap bolts are standing on the way surfaces. I could finish cleaning and installing the lathe and just make one, but as I said I’m inexperienced. It slides out easily after its off the screw. I can not tighten it dismsntling a snug fit between the center and the stock piece being turned. Here’s a quick link that shows what we’re talking about.

I am sure there is further adjustment required here. Check Mc Master for the nut. The bracket that holds the tailstock to the bed is trivial to remove.

I was hoping that someone could instruct me in the recommended way to dismantlibg the spindle itself from the tailstock and the nut from the tailstock spindle. Rear view without gear box. The nut itself 22 appears to be held in by two hex screws, but I’m not sure if the nut itself is threaded on the outside and screws into the tailstock spindle, if it is held in place with some sort of adhesive in addition to the screws, or if it is pressed in.

  ANALISIS MATEMATICO 1 EDUARDO ESPINOZA RAMOS SOLUCIONARIO PDF

The bottom of a tailstock is a precision component of a lathe. If you want to know more or withdraw your consent to all or some of the cookies, please refer to the cookie policy.

Reassembly was also quite easy. I could also be completely wrong Usually other confounding clues can lead you to some more understanding of the construction. Finally, the locking lever and mounting bracket are reinstalled. In German most stuff that spins and has a special function is called a Spindel yeah, the German word is that similar.

Be careful not to insert the wrench too deep so it engages the actual set screw before you have removed the lock screw on top. Your email address will not be published. Another key resource for advice and especially inspiration has been Kurt Bjornwho restored his HLV machine.

But we haven’t helped the poor guy trying to take his apart. It is keyed all the way to the back of the part so that it can be removed towards the front.

Assemblj the set screws are out, you should be able to slide the pulley back toward the tailstock end and lift off the belt. View into the headstock from below with the counter shaft speed control removed. It’s held in place by a dog point setscrew that must be removed first. Completely forgot about that method, since the only time I’ve used it was on a bigger lathe to get a too short live center out, and that lathe has been gone for quite a while.