ELTAKO TLZ12-8E-230V UC PDF

Manufacturer name, Eltako. Manufacturer number, TLZEV+UC. GTIN, Country of origin, Germany. Customs tariff number, gThe Standardg TLZ12 8E 23 V UC replaces the TLZ12N0 V and TLZ12 8E V+V uC. gThe Allrounderg TLZ12D 23 V UC replaces the TLZ12M V+V uC. g The Simpleg . Also visit TLZ12D V +UC. Eltako Staircase time switch TLZplus 1; 2; 3; 4 Matching products. Eltako Staircase time switchTLZ Manufacturer, Eltako. Manufacturer.

Author: Faudal Goltilrajas
Country: Algeria
Language: English (Spanish)
Genre: Business
Published (Last): 24 February 2007
Pages: 18
PDF File Size: 5.57 Mb
ePub File Size: 10.70 Mb
ISBN: 206-9-49898-846-9
Downloads: 25925
Price: Free* [*Free Regsitration Required]
Uploader: Arashitilar

Eltako Tlz61np230v UC Timer per Luce

This results in an additional tlz12-8e-320v consumption of only 0. With the Eltako Duplex technology DX the normally potential-free contacts can still switch in zero passage when switching V AC 50 Hz and therefore drastically reduce wear.

Contact gap 3 mm. Housing without front panel to insert operating instructions.

Eltako Treppenlicht Zeitschalter Tlz12-8e-230v UC

If the channels are used to control switchgear that has no zero passage switching, N should not be connected, otherwise the additional off-delay would have the opposite effect.

Display up to 9, kWh with 3 decimal digits, from 10kWh with 1 decimal digit and from kWh without decimal digit. Manual control has priority over all other control commands. Technical data page B First the background lighting switches on.

Multifunction time relays always switch at zero passage, the DX devices only when connected to N. Wind sensor WS The WS wind sensor provides a sequence of pulses as a function of the wind vane speed.

  GEOGRAFIA URBANA JACQUELINE BEAUJEU GARNIER PDF

The GBA12 page Z2. Any assignment of control devices to the switchgear devices can be chosen, and provision is made for easy modi cations,retro tting and expansion, “bit by bit”.

Руководства для переключателей и реле | Eltako

With the rotary switch WA automatic reversal is controlled: Technical data page I4. This impulse switch represents the latest generation of electronic switchgear: Due to its low residual ripple, it generates no measurable alternating field even at V DC. At the control input push-buttons with a glow lamp current up to 50 mA can be connected. B6 Function rotary switch Standard setting ex factory.

Local control with dual roller shutter push-button connected to A5 and A6. With double connections for push-button and lamp in order to connect either above or below or only below. A full telegram comprising meter reading and power status is transmitted every 10 minutes.

A glow lamp current is not permitted.

ELTAKO – [PDF Document]

The set release delay RV delay time starts when the control contact opens and if a set operating delay has elapsed. Degree of protection IP According to the directive all new types of meters must comply with the requirements of the directive as from 30 October For this reason, direct sales to end-users, e.

If the connection is incorrectly wired, the display shows the message ‘false’. Housing for operating instructions GBA12 page Z2. Product group G, page G3.

  ENSAYOS DANTESCOS DE BORGES PDF

When you confirm the flashing display LCK by pressing SET, the buttons are locked and this is indicated by an arrow in field 1 pointing in the direction of the lock icon sticker. The lower rotary switch sets 10 different functions: When energy saving lamps ESL are completely or partially switched, then set the switch-off early warning with the push-button permanent light ESL on the lower rotary switch. We use cookies to save your settings and to immediately show you the right price information next time you visit our site.

Universal control voltage 8 to V UC. A glow lamp current up to mA is permitted for particular device. Sensor function and open circuit monitoring If the signal from the light sensor or the wind sensor is missing for 24 hours, then an alarm is triggered: On the energy consumption indicator, a maximum of 5 out of 10 LEDs light up simultaneously, and the last clockwise LED lights up the brightest.

To achieve this, simply connect the N conductor to the terminal N and the phase conductors to 1 L3 L or 5 L. The changeover buttons are blue.