IC 74245 PDF

Lead Small Outline Integrated Circuit (SOIC), JEDEC MS, Wide. DM74LSSJ. M20D. Lead Small Outline Package (SOP), EIAJ TYPE II. 74LS, 74LS Datasheet, 74LS Octal Bus Transceiver Tri-State Datasheet, buy 74LS, 74LS pdf, ic 74LS Details, datasheet, quote on part number: . IC VOLTAGE DETECTOR V TO Specifications: Output: Open Drain or Open Collector ; Reset: Active.

Author: Kazikazahn Shajin
Country: Ghana
Language: English (Spanish)
Genre: Automotive
Published (Last): 16 July 2017
Pages: 498
PDF File Size: 17.81 Mb
ePub File Size: 7.19 Mb
ISBN: 128-4-16730-636-6
Downloads: 68781
Price: Free* [*Free Regsitration Required]
Uploader: Yorr

Of course, it is not a question to hope the clock pulses up to to check the table: This is symbolized jc a bubble placed on the entry f1 in figure It presents a luminosity weaker than the normal. The most significant bit M. After the sixteenth clock pulse, the incrementing of the indication of the bill-posters starts, this one being in hexadecimal code, of 00 to finish to FF at the end of counting.

To check if the 774245 goes indeed from B8 towards A8repeat the same procedure as for the preceding case. Observe what occurs on A8.

The door of entry NAND is followed of a trigger of Schmitt who is used to improve quality of the signal, then come two reversers which control the chain of dividers.

Rock then SW1 on position 0 to validate the circuit again. To carry out the following experiments, it will be necessary to use a meter. Click here for the following lesson or in the synopsis envisaged to this end.

Operational test of a Icc on 12 floors. The electric diagram of the circuit carried out is represented figure b, while the figure c represents its synoptic diagram. By observing the LED and the bill-posterscheck the correct operation of the meter by consulting the table of figure L0 and L1 flicker then at the rate of 10 Hz. To carry out the experiments envisaged in this practice, it will be necessary for you to use the following material: This is due to the fact that the exit of door 2 of figure 15 is at the high level whereas that of door 1 is on the bottom grade thus prohibiting the B8 direction towards A8.

  DESHEREDADA GALDOS PDF

Static page 7425 welcome.

You have just checked the two directions of transmission of the signal between A8 and B8 of the one of the eight ways of the integrated circuit. The table of figure 23 indicates the frequency and the period of the signals of the various stages of the meter and summarizes the test results. In the preceding practices, you tried out various types of meters ; that that you will examine now is not different from the others as for its design, but it has the great advantage of containing 12 stages in a single integrated circuit.

Electronic forum and Poem. The meter can go from 0 to 2 12 positions.

Datasheet(PDF) – Fairchild Semiconductor

The meter is incremented each time the entry f1 passes from the high level on the bottom grade, i. It is about the CDbinary asynchronous meter with 12 bitswhose synoptic diagram is represented figure As you can note it, the frequencies spread out of lc Hz with 0, Hzi.

The stitching of this circuit is indicated on oc It must be in position OFF at the time of its connection on the sector. By basing you on the results obtained, you can build the table of operation of the bidirectional buffer indicated figure 17 which can be summarized schematically by figure You thus noted that L1 can be ordered independently of the buffer which, lc validated, does not intervene. To contact the author. Adopt the same procedure for the seven other ways in order to check correct operation.

At boundaries 2, 3, 4, 5, 6, 7, 8 and 9 can be connected eight lines of A1 to A87445 eight others can be connected to pins 18, 17, 16, 7245, 14, 13, 12 and 11 of B1 with B8. Indeed, when SW0 is in position 1the passage of the signal in the direction of A8 with B8 is authorized. Electronic forum and Infos. Indeed, L0 still flickers, ordered by the signal coming from CP1 ; on the other hand L1 does not flicker any more. L and that, for this reason, it must be fed with a stable tension of 5 V.

  JURISCOPE OHADA PDF

High of page Preceding page Following page.

Form of the perso pages. By commenting on the experiment, one can say that each stage of the meter carries out a division by two uc the frequency of the signal applied to its entry ; if one injects the signal with 10 Hzcoming from contact CP1at the entry f 1 of the meter, the various exits, one obtains signals whose frequency is each if reduced by half. In this first phase, you will check the operation of the one of the eight bidirectional buffers of the integrated circuit.

You can notice the sign represented inside each buffer ; it indicates that the buffers used comprise a circuit of re-arrangement of the trigger type of Schmitt. On the twelve exits of Q1 with Q12one finds a number binary of twelve bits active of: 7445 page of welcome.

How to make a site? Now reverse the direction of transmission by applying the rectangular signal provided by CP1 to the B8 entry. A higher tension 7424 damage it. Forms maths Geometry Physics 1.

Carry out then the connections necessary. Return to the synopsis. L1 ignites ci its full intensity. The figure b represents the diagram of the electric circuit carried out.

IC 74LS245/74245 DIP20

Will finally know kc the circuit 74LS is a circuit of technology T. The entry RESET gives the meter to zero, it is asynchronous ; as soon as a level H is applied to him, the meter passes to 0. It is thus enough to a little attention to observe the phenomenon and if there would remain some points obscure, do not hesitate to start again several times the experiment.